This is an old revision of the document!
Table of Contents
MB7AZE : allstar
| Platform | Rapsberry Pi |
| Connectivity | All Star Node 481481 |
| Interface | CM108 Soundcard |
| Radio | FT-8900 |
| Frequency | 430.050MHz |
| Monitor | Supermon |
Commands
- DTMF Commands
- Please send * 7 3 to ensure all links are disconnected before making any new links
| Command | DTMF Sequence |
|---|---|
| Disconect from Node xxxx | * 1 xxxx |
| Connect RX Only to xxxx | * 2 xxxx |
| Connect Transceive to xxxx | * 3 xxxx |
| Speak the Node Status | * 7 0 |
| Disconnect ALL nodes | * 7 3 |
| Reconnect ALL nodes | * 7 4 |
| Send Node ID | * 8 0 |
| Speak the Local Time | * 8 1 |
| Parrot ON | * 9 1 |
| Parrot OFF | * 9 2 |
| Parrot ONCE | * 9 3 |
To connect to an Echolink Node make node number 6 figures long with leading 0 s where needed and indicate it's an “Echolink” node with an extra leading 3 after usual connect sequence (* 3 )
For example to connect to 9999
* 3 3 0 0 9 9 9 9
| Number | Name | * 5 Macro shortcut to… | DTMF Sequence | Node No. |
|---|---|---|---|---|
| 1 | Hubnet | Connect RX Only to Hubnet | * 5 2 1 | 41223 |
| 1 | Hubnet | Connect Transceive to Hubnet | * 5 3 1 | 41223 |
| 1 | Hubnet | Disconnect from Hubnet | * 5 1 1 | 41223 |
| 2 | FreeNet | Connect RX Only to FreeNet | * 5 2 2 | 2197 |
| 2 | FreeNet | Connect Transceive to FreeNet | * 5 3 2 | 2197 |
| 2 | FreeNet | Disconnect from FreeNet | * 5 1 2 | 2197 |
| 3 | CQ North | Connect RX Only to CQ North | * 5 2 3 | 54383 |
| 3 | CQ North | Connect Transceive to CQ North | * 5 3 3 | 54383 |
| 3 | CQ North | Disconnect from CQ North | * 5 1 3 | 54383 |
| 4 | Alaska | Connect RX Only to Alaska Morning Net | * 5 2 4 | 29332 |
| 4 | Alaska | Connect Transceive to Alaska Morning Net | * 5 3 4 | 29332 |
| 4 | Alaska | Disconnect from Alaska Morning Net | * 5 1 4 | 29332 |
| Hubnet Echo | Connect to Hubnet Echotest (40894) | * 5 3 9 1 | 40894 | |
| Hubnet Echo | Disconnect from Hubnet Echotest (40894) | * 5 1 9 1 | 40894 | |
| Echolink Echo | Connect to Echolink Echotest(3009999) | * 5 3 9 2 | 3009999 | |
| Echolink Echo | Disconnect from Echolink Echotest(3009999) | * 5 1 9 2 | 3009999 |
Courtesy Tones
Can give information about the node status.
After a local Transmission on the “input” frequency the reponse will be one of:
- Morse Letter I (di-dit) = node is not connected to any other nodes
- Morse Letter R (di-dah-dit) = node is connected in “Monitor/RX only” mode to one or more nodes
- Morse Letter K (dah-di-dah) = node is connected in “Transceive” mode to one or more nodes
There are other tones, e.g. when a station on a linked node unkeys there's a low-pitched “bloop”
When a local RF station sends a command there's a “bip bip” (not to be confused with the Morse letter I)
Echolink
AllStar nodes can also connect to Echolink
The node is connected to Echolink as MB7AZE-L #879598
Page Info
Page created Sun May 29 12:18:09 2022 by John Pumford-Green
Page last updated: 30/12/25 09:55 GMT