MB7AZE AllStar Config

Try to learn something about everything, and everything about somethingThomas Huxley “Darwin's bulldog” (1824-1895)
Trace: • MB7AZE AllStar • VHF / HF Xgate 2024 • Pinouts • K2 - 2023 • HF Utilities • Xeigu G90 • Fldigi Parrot • QSO Logging • YaDDNet • Cadet Radio Info
You are here: Home » Public Area » Radio » Radio Topics » AllStar Linking » MB7AZE AllStar Config
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
<-[[.:start]]


====== MB7AZE AllStar Config ======



===== Main Config files =====

==== echolink.conf ====

++++ /etc/asterisk/echolink.conf |
<code>
[el0]
call = MB7AZE-L                          ; Change this!
pwd = xxxxxxxx                           ; Change this!
name = John                        ; Change this!
qth = allstar 481481                           ; Change this!
email = gm4slv@gm4slv.plus.com                         ; Change this!
node = 879598                           ; Change this!
; Data for EchoLink Status Page
lat = 60.2883                               ; Latitude in decimal degrees
lon = -001.42533                               ; Longitude in decimal degrees
freq = 430.050                              ; not mandatory Frequency in MHz
tone = 0.0                              ; not mandatory CTCSS Tone (0 for none)
power = 1                               ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts)
height = 0                              ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet)
gain = 0                                ; Gain in db (0-9)
dir = 0                                 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction)
maxstns = 5                            ; Max Stations

rtcptimeout = 10
recfile = /tmp/echolink_recorded.gsm    ;
astnode = 481481             ; Change this!
context = radio-secure                  ; Default in code is echolink-in

; Max 3 servers
server1 = nasouth.echolink.org
server2 = naeast.echolink.org
server3 = server3.echolink.org

; To deny w6xxx you would add the statement: deny = w6xxx
; To prohibit computer-based connections you would write: permit = *-*
; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
; permit                                ; comma delimited list of callsign, type (-r)
; deny


; Remote text commands thru netcat:
; o.conip <IPaddress>    (request a connect)
; o.dconip <IPaddress>   (request a disconnect)
; o.rec                  (turn on/off recording)

; ipaddr
; port

</code>
++++

==== manager.conf ====

++++ /etc/asterisk/manager.conf |

<code>
;
; Asterisk Call Management support
;

; By default asterisk will listen on localhost only. 
[general]
enabled = yes
port = 5038
bindaddr = 127.0.0.1

[gm4slv]
secret = llcgi
read = all,system,call,log,verbose,command,agent,user,config
write = all,system,call,log,verbose,command,agent,user,config
</code>
++++

==== rpt.conf ====

++++ /etc/asterisk/rpt.conf |

<code>
; Radio Repeater configuration file (for use with app_rpt)
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;
; This is where you define your nodes which can be connected to.
;

[nodes]
; Note, if you are using automatic update for allstar link nodes,
; no allstar link nodes should be defined here. Only place a definition
; for your local nodes, and private (off of allstar link) nodes here.

;481480 = radio@127.0.0.1:4569/481480,NONE	; This must be changed to your node number
481481 = radio@127.0.0.1:4569/481481,NONE	; This must be changed to your node number
                                        ; and iax port number if not the default

;[481480]					; Change this to your assigned node number
[481481]					; Change this to your assigned node number

                                        ; Must also be enabled in modules.conf
					; Rx audio/signalling channel. Choose ONLY 1 per node stanza

					; Enable the selected channel driver in modules.conf !!!
;rxchannel = dahdi/pseudo	        ; No radio (hub)
 rxchannel = SimpleUSB/usb_48148	; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_48148		; USBRadio (DSP)
; rxchannel = Dahdi/1			; PCI Quad card
; rxchannel = Beagle/1			; BeagleBoard
; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/48148                ; RTCM device


duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.
                                        ;     Special Case: Full duplex if linktolink is set to yes.
                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.
					;     Comment out idrecording and idtalkover to suppress IDs also
                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.
                                        ;     This mode is preferred when interfacing a simplex node.
                                        ; 2 = Full Duplex with telemetry tones and hang time.
                                        ;     This mode is preferred when interfacing a repeater.
                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.
                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

linktolink = no				; disables forcing physical half-duplex operation of main repeater while
					; still keeping half-duplex semantics (optional)

linkmongain = 0				; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.
					; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.
					; If linkmongain set to a positive number monitored audio will increase by the set amount in db.
					; The value of linkmongain is in db. The default value is 0 db.

erxgain = -3				; Echolink receive gain adjustment
					; Note: Gain is in db-volts (20logVI/VO)
etxgain = 3				; Echolink transmit gain adjustment
					; Note: Gain is in db-volts (20logVI/VO)
eannmode = 2                           ; 1 = Say only node number on echolink connects (default = 1)
                                        ; 2 = say phonetic call sign only on echolink connects
                                        ; 3 = say phonetic call sign and node number on echolink connects

;controlstates = controlstates		; system control state stanza

scheduler = schedule			; scheduler stanza
functions = functions			; Repeater Function stanza
phone_functions = functions		; Phone Function stanza
link_functions = functions		; Link Function stanza

telemetry = telemetry			; Telemetry stanza
morse = morse				; Morse stanza
wait_times = wait-times			; Wait times stanza

context = radio				; dialing context for phone
callerid = "Repeater" <0000000000>	; callerid for phone calls
accountcode = RADIO                     ; account code (optional)

hangtime = 200				; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)
althangtime = 300			; longer squelch tail
totime = 300000				; 5 mins (12/4/22) transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

telemnomdb = -3				;
telemduckdb = -10			;

;idrecording = /home/gm4slv/gm4slv_id
;idrecording = /home/gm4slv/mb7aze_id
idrecording = |iDE MB7AZE			; Main ID message

;idtalkover = |iMB7AZE			; Talkover ID message
idtalkover = |iMB7AZE			; Talkover ID message
					; See Telemetry section Example: idrecording = rpt/nodenames/48148
idtime = 900000				; 15 mins (12/4/22) id interval time (in ms) (optional) Default 5 minutes (300000 ms)
politeid = 30000			; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

unlinkedct = ct12			; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)
remotect = ct3				; remote linked courtesy tone (indicates a remote is in the list of links)
linkunkeyct = ct4			; sent when a transmission received over the link unkeys
;nolocallinkct = 0			; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

; Supermon smlogger
connpgm=/usr/local/sbin/supermon/smlogger 1
discpgm=/usr/local/sbin/supermon/smlogger 0

;connpgm = yourconnectprogram		; Disabled. Execute a program you specify on connect. (default)
					; passes 2 command line arguments to your program:
					; 1. node number in this stanza (us)
					; 2. node number being connected to us (them)
;discpgm = yourdisconnectprogram	; Disabled. Execute a program you specify on disconnect. (default)
					; passes 2 command line arguments to your program:
					; 1. node number in this stanza (us)
					; 2. node number being disconnected from us (them)

lnkactenable = 0			; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

lnkacttime = 3600			; Link activity timer time in seconds.
lnkactmacro = *73			; Function to execute when link activity timer expires.
lnkacttimerwarn = custom/timeout		; Message to play when the link activity timer has 30 seconds left.

;remote_inact_timeout =	60		; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)
;remote_timeout =			; Session time out for remote base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq =		; 30
;remote_timeout_warning =		; (3 * 60)

;nounkeyct = 0				; Set to a 1 to eliminate courtesy tones and associated delays.

holdofftelem = 0			; Hold off all telemetry when signal is present on receiver or from connected nodes
					; except when an ID needs to be done and there is a signal coming from a connected node.

telemdefault = 1                        ; 0 = telemetry output off
                                        ; 1 = telemetry output on (default = 1)
                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,
                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

beaconing = 1				; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

parrotmode = 1				; 0 = Parrot Off (default = 0)
					; 1 = Parrot On Command
					; 2 = Parrot Always
					; 3 = Parrot Once by Command

parrottime = 1000			; Set the amount of time in milliseconds
					; to wait before parroting what was received

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified
                                        ; b/w. app_rpt must have been compiled with
                                        ; the notch option

startup_macro = *80*81*70

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign	; Point to alternate nodename sound directory

; Stream your node audio to Broadcastify or similar. See https://wiki.allstarlink.org/wiki/Stream_Node_Audio_to_Broadcastify
; outstreamcmd = /bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - | /usr/bin/ezstream -qvc /etc/ezstream.xml

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more information on these

;extnodes = extnodes-different	; section in extnodefile containing dynamic node information (optional)
;extnodefile = /home/gm4slv/rpt_extnodes	; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)
;extnodefile2 =			; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????
;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames
;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)
;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set
;                               ; to support tail messages. They can be omitted otherwise.
;tailmessagetime = 300000       ; Play a tail message every 5 mins
;tailsquashedtime = 30000       ; If squashed by another user,
;                               ; try again after 30 seconds
;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

; alt_functions
; ctgroup
; dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars		Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
; propagate_phonedtmf
; rptnode
; rptinactmacro  Macro to execute when inactivity timer expires
; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)
; rxnotch	Optional Audio notch
; simplexphonedelay
; tonemacro
; tonezone
; txlimits


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


; *** Status Reporting ***

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org
statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

[functions]

; Prefix	Functions
; *1		Disconnect Link
; *2		Monitor Link
; *3		Connect Link
; *4		Command Mode
; *5		Macros
; *6		User Functions
; *7		Connection Status/Functions
; *8		User Functions
; *9		User Functions
; *0		User Functions

; *A		User Functions
; *B		User Functions
; *C		User Functions
; *D		User Functions


; Mandatory Command Codes
1 = ilink,1		; Disconnect specified link
2 = ilink,2		; Connect specified link -- monitor only
3 = ilink,3		; Connect specified link -- tranceive
4 = ilink,4		; Enter command mode on specified link

70 = ilink,5		; System status

;99 = cop,6              ; PTT (phone mode only)

; End Mandatory Command Codes

73 = ilink,6		; Disconnect All Links
74 = ilink,16		; Reconnect links disconnected with "disconnect all links"

80 = status,11         ; Force ID (local only)
81 = status,12         ; Give Time of Day (local only)

91 = cop,21		; Enable Parrot Mode
92 = cop,22		; Disable Parrot Mode
93 = cop,55		; Parrot Once if parrot mode is disabled

98 = cop,2		; System enable
99 = cop,3		; System disable

901 = cop,1				; System warm boot

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Macro Commands
5 = macro

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Autopatch Commands
; Note, This may be a good place for other 2 digit frequently used commands

;61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up
;62 = autopatchdn                                                 ; Autopatch down

; autopatchup can optionally take comma delimited setting=value pairs:

; context = string		; Override default context with "string"
; dialtime = ms			; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)
; farenddisconnect = 1		; Automatically disconnect when called party hangs up
; noct = 1			; Don't send repeater courtesy tone during autopatch calls
; quiet = 1			; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up
				; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Status Commands

; 1 - Force ID (global)
; 2 - Give Time of Day (global)
; 3 - Give software Version (global)
; 4 - Give GPS location info
; 5 - Last (dtmf) user
; 11 - Force ID (local only)
; 12 - Give Time of Day (local only)

;721 = status,1          ; Force ID (global)
;722 = status,2          ; Give Time of Day (global)
;723 = status,3          ; Give software Version (global)
;724 = status,4          ; Give GPS location info
;725 = status,5          ; Last (dtmf) user



;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Link Commands

; 1 - Disconnect specified link
; 2 - Connect specified link -- monitor only
; 3 - Connect specified link -- tranceive
; 4 - Enter command mode on specified link
; 5 - System status
; 6 - Disconnect all links
; 7 - Last Node to Key Up
; 8 - Connect specified link -- local monitor only
; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
; 10 - Disconnect all RANGER links (except permalinks)
; 11 - Disconnect a previously permanently connected link
; 12 - Permanently connect specified link -- monitor only
; 13 - Permanently connect specified link -- tranceive
; 15 - Full system status (all nodes)
; 16 - Reconnect links disconnected with "disconnect all links"
; 17 - MDC test (for diag purposes)
; 18 - Permanently Connect specified link -- local monitor only

; ilink commands 1 through 5 are defined in the Mandatory Command section

;806 = ilink,6			; Disconnect all links
;827 = ilink,7			; Last Node to Key Up
;808 = ilink,8			; Connect specified link -- local monitor only
;809 = ilink,9,48148,"Testing"	; would send a text message to node 48148 replace 48148 with 0 for all connected nodes
;810 = ilink,10			; Disconnect all RANGER links (except permalinks)
;811 = ilink,11			; Disconnect a previously permanently connected link
;812 = ilink,12			; Permanently connect specified link -- monitor only
;823 = ilink,13			; Permanently connect specified link -- tranceive
;815 = ilink,15			; Full system status (all nodes)
;817 = ilink,17			; MDC test (for diag purposes)
;818 = ilink,18			; Permanently Connect specified link -- local monitor only

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Control operator (cop) functions.
; Change these to something other than these codes listed below!
; Uncomment as needed.

;901 = cop,1				; System warm boot

; 904 = cop,4				; Test tone on/off (toggle)
; 905 = cop,5				; Dump system variables on console (debug use only)

; 907 = cop,7				; Time out timer enable
; 908 = cop,8				; Time out timer disable

; 909 = cop,9				; Autopatch enable
; 910 = cop,10				; Autopatch disable

; 911 = cop,11				; User linking functions enable
; 912 = cop,12				; User linking functions disable

; 913 = cop,13				; Query system control state
; 914 = cop,14				; Set system control state

; 915 = cop,15				; Scheduler enable
; 916 = cop,16				; Scheduler disable

; 917 = cop,17				; User functions enable (time, id, etc)
; 918 = cop,18				; User functions disable

; 919 = cop,19				; Select alternate hang time (althangtime)
; 920 = cop,20				; Select standard hangtime (hangtime)


; 924 = cop,24				; Flush all telemetry
; 925 = cop,25				; Query last node un-keyed
; 926 = cop,26				; Query all nodes keyed/unkeyed
; 927 = cop,27				; Reset DAQ minimum on a pin
; 928 = cop,28				; Reset DAQ maximum on a pin

; 930 = cop,30				; Recall Memory Setting in Attached Xcvr

; 931 = cop,31				; Channel Selector for Parallel Programmed Xcvr

; 932 = cop,32				; Touchtone pad test: command + Digit string + # to playback all digits pressed

; 933 = cop,33				; Local Telemetry Output Enable
; 934 = cop,34				; Local Telemetry Output Disable
; 935 = cop,35				; Local Telemetry Output on Demand

; 936 = cop,36				; Foreign Link Local Output Path Enable
; 937 = cop,37				; Foreign Link Local Output Path Disable
; 938 = cop,38				; Foreign Link Local Output Path Follows Local Telemetry
; 939 = cop,39				; Foreign Link Local Output Path on Demand

; 942 = cop,42				; Echolink announce node # only
; 943 = cop,43				; Echolink announce node Callsign only
; 944 = cop,44				; Echolink announce node # & Callsign

; 945 = cop,45				; Link Activity timer enable
; 945 = cop,46				; Link Activity timer disable
; 947 = cop,47				; Reset "Link Config Changed" Flag

; 948 = cop,48				; Send Page Tone (Tone specs separated by parenthesis)

; 949 = cop,49				; Disable incoming connections (control state noice)
; 950 = cop,50				; Enable incoming connections (control state noicd)

; 951 = cop,51				; Enable sleep mode
; 952 = cop,52				; Disable sleep mode
; 953 = cop,53				; Wake up from sleep
; 954 = cop,54				; Go to sleep

; 956 = cop,56                            ; Rx CTCSS Enable
; 957 = cop,57                            ; Rx CTCSS Disable

; 958 = cop.58                            ; Tx CTCSS On Input only Enable
; 959 = cop,59                            ; Tx CTCSS On Input only Disable

; 960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
;                                         ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
;                                         ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.
;                                         ; DestID and subcode are only specified for  the 'C' type message.
;                                         ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of
;                                         ; the radio being called, and the subcodes are as follows:
;                                         ; Subcode '8205' is Voice Selective Call for Spectra ('Call')
;                                         ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or
;                                         ; Astro-Saber('Call')
;                                         ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

; 961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
; 962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

; 963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])
; 964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
; 965 = cop,65                            ; Send POCSAG page (equipped channel types only)

[functions-remote]

0 = remote,1                            ; Retrieve Memory
1 = remote,2                            ; Set freq.
2 = remote,3                            ; Set tx PL tone
3 = remote,4                            ; Set rx PL tone
40 = remote,100                         ; Rx PL off
41 = remote,101                         ; Rx PL on
42 = remote,102                         ; Tx PL off
43 = remote,103                         ; Tx PL on
44 = remote,104                         ; Low Power
45 = remote,105                         ; Medium Power
46 = remote,106                         ; High Power
711 = remote,107                        ; Bump -20
714 = remote,108                        ; Bump -100
717 = remote,109                        ; Bump -500
713 = remote,110                        ; Bump +20
716 = remote,111                        ; Bump +100
719 = remote,112                        ; Bump +500
721 = remote,113                        ; Scan - slow
724 = remote,114                        ; Scan - quick
727 = remote,115                        ; Scan - fast
723 = remote,116                        ; Scan + slow
726 = remote,117                        ; Scan + quick
729 = remote,118                        ; Scan + fast
79 = remote,119                         ; Tune
51 = remote,5                           ; Long status query
52 = remote,140				; Short status query
67 = remote,210				; Send a *
69 = remote,211				; Send a #
;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.
                                        ; Define a different dtmf sequence for each user which is
                                        ; authorized to use the remote base to control access to it.
                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to
                                        ; the remote base and announce WB6NIL as being logged in.
                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to
                                        ; the remote base and announce WA6ZFT as being logged in.
                                        ; When the remote base is disconnected from the originating node, the
                                        ; user will be logged out. The LICENSETAG argument is used to enforce
					; tx frequency limits. See [txlimits] below.
85 = cop,6                              ; Remote base telephone key


[telemetry]

; Telemetry entries can be shared across all repeaters, or defined for each repeater.
; Can be a tone sequence, morse string, or a file
;
; |t - Tone escape sequence
;
; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)
; Single frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse escape sequence
;
; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the
; [morse] section.
;
; Follow with an alphanumeric string
;
; |i - Morse ID escape sequence
;
; Sends Morse code at the ID amplitude and ID frequency as defined in the
; [morse] section.
;
; path/to/sound/file/without/extension
;
; Send the sound if in place of a constructed tone. Do not include the file extension
; Example: ct8 = rpt/bloop
; Example: idrecording = rpt/nodenames/48148

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 = |t(660,880,150,2048)
ct3 = |t(440,0,150,4096)
ct4 = |t(550,0,150,2048)
ct5 = |t(660,0,150,2048)
ct6 = |t(880,0,150,2048)
ct7 = |t(660,440,150,2048)
ct8 = |t(700,1100,150,2048)
ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon = |mR
;remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only
remotetx = |mK
;remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)		; local courtesy tone when linked Trancieve mode
cmdmode = |t(900,903,200,2048)
;functcomplete = |mW
functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone = |t(350,440,30000,3072)
patchup = rpt/callproceeding
patchdown = rpt/callterminated

ct12 = |mI
ct13 = |mR

; As far as what the numbers mean,
; (000,000,010,000)
;   |   |   |   |-------amplitude
;   |   |   |-------------duration
;   |   |-------------------Tone 2
;   |-------------------------Tone 1

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)
; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

; Morse code parameters, these are common to all repeaters.

[morse]
speed = 18				; Approximate speed in WPM
frequency = 800				; Morse Telemetry Frequency
amplitude = 4096			; Morse Telemetry Amplitude
idfrequency = 1065			; Morse ID Frequency
idamplitude = 1024			; Morse ID Amplitude

;
; This section allows wait times for telemetry events to be adjusted
; A section for wait times can be defined for every repeater
;

[wait-times]
telemwait = 400                        ; Time to wait before sending most telemetry
idwait = 500                            ; Time to wait before starting ID
unkeywait = 200                        ; Time to wait after unkey before sending CT's and link telemetry
calltermwait = 2000                     ; Time to wait before announcing "call terminated"

; Memories for remote bases

[memory]
;00 = 146.580,100.0,m
;01 = 147.030,103.5,m+t
;02 = 147.240,103.5,m+t
;03 = 147.765,79.7,m-t
;04 = 146.460,100.0,m
;05 = 146.550,100.0,m

; Place command macros here

[macro]
11 = *141223# ; disc. hubnet
21 = *241223# ; monitor hubnet
31 = *341223# ; transceive hubnet

12 = *12197# ; disc Freestar
22 = *22197# ; monitor Freestar
32 = *32197# ; transceive Freestar

13 = *129332# ; disc Alaska
23 = *229332# ; monitor Alaska
33 = *329332# ; transceive Alaska

14 = *154383# ; disc CQ North
24 = *254383# ; monitor CQ North
34 = *354383# ; transceive CQ North

191 = *140894# ; disconnect hubnet Echo
391 = *340894# ; connect hubnet echo

192 = *13009999#	; dis echolink echotest
392 = *33009999#	; con echolink echotest



; Data Acquisition configuration

;[daq-list]
;device = device_name1
;device = device_name2

;Where: device_name1 and device_name2 are stanzas you define in this file

;device = daq-cham-1

; Device name

;[daq-cham-1]				; Defined in [daq-list]
;hwtype = uchameleon			; DAQ hardware type
;devnode = /dev/ttyUSB0			; DAQ device node (if required)
;1 = inadc				; Pin definition for an ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 = inp				; Pin definition for an input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 = in				; Pin definition for an input without a weak pullup resistor
;14 = out				; Pin definition for an output
;15 = out
;16 = out
;17 = out
;18 = out

;[meter-faces]

;face = scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre = offset to add before dividing with scalediv
; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).
; scalepost = offset to add after dividing with scalediv
;
;face = range(X-Y:word,X2-Y2:word,...),word/?,...
;face = bit(low-word,high-word),word/?,...
;
; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,
; or a question mark which is  a placeholder for the measured value.
;
;
; Battery voltage 0-20 volts
;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind direction
;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34 temperature sensor with 130 deg. F full scale
;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll (non alarmed)
;light = bit(ha/off,ha/on),ha/light,?

;[alarms]
;
;tag = device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique name for the alarm
;device = daq device to poll
;pin = the device pin to be monitored
;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it
;node = the node number to execute the function on
;func-low = the DTMF function to execute on a high to low transition
;func-high = the DTMF function to execute on a low to high transition
;
; a  '-' as a function name is shorthand for no-operation
;
;door = daq-cham-1,9,1,2017,*7,-
;pwrfail = daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several control operator functions to be changed at once using one command (good for scheduling)
;
;[controlstates]
;statenum = copcmd,[copcmd]...
;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation
;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation
;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

; Scheduler - execute a macro at a given time

[schedule]
;dtmf_function =  m h dom mon dow  ; ala cron, star is implied
;8 = 55 12 * * *   ; at midnight, execute macro 2.

; See https://wiki.allstarlink.org/wiki/Event_Management
[events]

#includeifexists custom/rpt.conf


</code>

++++

==== simpleusb.conf ====

++++ /etc/asterisk/simpleusb.conf |

<code>
; If you are going to use this channel driver, you MUST enable it in modules.conf
; change:
; noload => chan_simpleusb.so ;                   CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
; to:
; load => chan_simpleusb.so ;                   CM1xx USB Cards with Radio Interface Channel Driver (No DSP)

; SimpleUSB configuration

[general]

[usb_48148]

eeprom = 0              ; EEPROM installed: 0,1
                        ; 0 = no (default)
                        ; 1 = yes

hdwtype = 0		; Leave this set to 0 for USB sound fobs modified using
			; the instructions from usbfob.pdf. Use a setting of 
			; 1 is for Dingotel/Sph interfaces.

; Receiver parameters

rxboost = 0             ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
                        ; Set to 1 for additonal gain if using a low-level receiver output

carrierfrom = usb ; no,usb,usbinvert
                        ; no - no carrier detection at all
                        ; usb - from the COR line on the USB sound fob (Active high)
                        ; usbinvert - from the inverted COR line on the USB sound fob (Active low)

ctcssfrom = no		; no,usb,usbinvert
                        ; no - CTCSS decoding, system will be carrier squelch
                        ; usb - CTCSS decoding using input from USB sound fob (Active high)
                        ; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low)

deemphasis = yes         ; enable de-emphasis (input from discriminator)

plfilter = no           ; enable PL filter

;rxondelay = 0		; number of 20ms intervals to hold off receiver turn-on indication


; Transmitter parameters

txmixa = voice          ; Left channel output (A): no,voice
                        ; no - Do not output anything
                        ; voice - output voice only

txmixb = no		; Right channel output (B): no,voice
                        ; no - Do not output anything
                        ; voice - output voice only

txboost = 0

invertptt = 0           ; Invert PTT: 0,1
                        ; 0 - ground to transmit
                        ; 1 - open to transmit

preemphasis = yes	; Perform standard 6db/octave pre-emphasis

; pager = no            ; no,a,b (e.g. pager = b means "put the normal repeat audio on channel A, and the pager audio on channel B")

; duplex3 = 0           ; duplex 3 gain setting (0 to disable)

duplex = 0              ; Duplex 0,1
                        ; 0 - half duplex
                        ; 1 - full duplex

#includeifexists custom/simpleusb.conf

</code>

++++

==== simpleusb_tune_usb_48148.conf ====

++++ /etc/asterisk/simpleusb_tune_usb_48148.conf |

<code>
[usb_48148]
; name=usb_48148
; devicenum=1
devstr=1-1.2:1.0
rxmixerset=330
txmixaset=70
txmixbset=50

</code>

++++


==== crontab ====

''00 * * * * sudo /usr/sbin/asterisk -rx "rpt localplay 481481 /home/gm4slv/mb7aze_id " >/dev/null 2>&1''

''00 * * * * sleep 4 && sudo /usr/sbin/asterisk -rx "rpt fun 481481 *81" >/dev/null 2>&1''

 

Page created Sun May 29 15:48:50 2022 by John Pumford-Green

Page last updated: ~~LASTMOD~~

{{tag>pi radio allstar mb7aze}}
Navigation

Search

Toolbox
