Differences

This shows you the differences between two versions of the page.

--- public:radio:mb7aze_allstar [05/06/22 09:58 BST] – [Commands] john
+++ public:radio:mb7aze_allstar [26/04/23 14:46 BST] (current) – removed john
@@ Line 1: / Line 1: @@
-<-[[.:start]]
-====== MB7AZE : allstar ======
-|Platform|Rapsberry Pi|
-|Connectivity|[[Allstar|All Star Node 481481]]|
-|Interface|CM108 Soundcard|
-|Radio|FT-8900|
-|Frequency|430.050MHz|
-|Monitor|[[http://gm4slv.plus.com:42111/supermon/link.php?nodes=481481|Supermon]]|
-[[https://ukrepeater.net/my_repeater.php?id=4823|NoV issued April 2022]]
-===== Commands =====
-  * DTMF Commands
-  * Please send * 7 3 to ensure all links are disconnected before making any new links
-^Command	^DTMF Sequence^
-|Disconect from Node xxxx	|  * 1 xxxx  |
-|Connect RX Only to xxxx	|  * 2 xxxx  |
-|Connect Transceive to xxxx	|  * 3 xxxx  |
-|Speak the Node Status	|  * 7 0  |
-|Disconnect ALL nodes	|  * 7 3  |
-|Reconnect ALL nodes	|  * 7 4  |
-|Send Node ID	|  * 8 0  |
-|Speak the Local Time	|  * 8 1  |
-|Parrot ON	|  * 9 1  |
-|Parrot OFF	|  * 9 2  |
-|Parrot ONCE	|  * 9 3  |
-To connect to an Echolink Node make node number 6 figures long
-with leading 0 s where needed and indicate it's an "Echolink"
-node with an extra leading 3 after usual connect sequence (* 3 )
-''For example to connect to 9999''
-''* 3 3 0 0 9 9 9 9''
-^Number^Name^* 5 Macro shortcut to...	^DTMF Sequence^Node No.|
-|  1  |  Hubnet  |Connect RX Only to Hubnet	|  * 5 2 1  |  41223  |
-|  1  |  Hubnet  |Connect Transceive to Hubnet	|  * 5 3 1  |  41223  |
-|  1  |  Hubnet  |Disconnect from Hubnet	|  * 5 1 1  |  41223  |
-|  2  |  FreeNet  |Connect RX Only to FreeNet	|  * 5 2 2  |  2197  |
-|  2  |  FreeNet  |Connect Transceive to FreeNet	|  * 5 3 2  |  2197  |
-|  2  |  FreeNet  |Disconnect from FreeNet	|  * 5 1 2  |  2197  |
-|  3  |  CQ North  |Connect RX Only to CQ North	|  * 5 2 3  |  54383  |
-|  3  |  CQ North  |Connect Transceive to CQ North	|  * 5 3 3  |  54383  |
-|  3  |  CQ North  |Disconnect from CQ North	|  * 5 1 3  |  54383  |
-|  4  |  Alaska  |Connect RX Only to Alaska Morning Net	|  * 5 2 4  |  29332  |
-|  4  |  Alaska  |Connect Transceive to Alaska Morning Net	|  * 5 3 4  |  29332  |
-|  4  |  Alaska  |Disconnect from Alaska Morning Net	|  * 5 1 4  |  29332  |
-|  |  Hubnet Echo  |Connect to Hubnet Echotest (40894)	|  * 5 3 9 1  |  40894  |
-|  |  Hubnet Echo  |Disconnect from Hubnet Echotest (40894)	|  * 5 1 9 1  |  40894  |
-|  |  Echolink Echo  |Connect to Echolink Echotest(3009999)	|  * 5 3 9 2  |  3009999  |
-|  |  Echolink Echo  |Disconnect from Echolink Echotest(3009999)	|  * 5 1 9 2  |  3009999  |
-===== Courtesy Tones =====
-Can give information about the node status.
-After a local Transmission on the "input" frequency the reponse will be one of:
-  * Morse Letter **I** (di-dit) = node is not connected to any other nodes
-  * Morse Letter **R** (di-dah-dit) = node is connected in "Monitor/RX only" mode to one or more nodes
-  * Morse Letter **K** (dah-di-dah) = node is connected in "Transceive" mode to one or more nodes
-There are other tones, e.g. when a station on a linked node unkeys there's a low-pitched "bloop"
-When a local RF station sends a command there's a "bip bip" (not to be confused with the Morse letter I)
-==== Echolink ====
-AllStar nodes //can// also connected to [[https://www.echolink.org/logins.jsp|Echolink]]
-My Echolink node is ''MB7AZE-L #879598''
-/*
-(**UPDATE** --- //John Pumford-Green 01/06/22 17:21// )
-I have disabled the Echolink connection by editing ''/etc/asterisk/modules.conf'' to change the channel driver for Echolink to ''noload'' ->
-<code conf>
-noload => chan_echolink.so ;
-</code>
-an Asterisk reload is necessary:
-<code bash>
-gm4slv@mb7aze:/etc/asterisk$ sudo astres.sh
-Restarting Asterisk
-systemctl restart asterisk.service
-</code>
-*/
-==== Page Info ====
-Page created Sun May 29 12:18:09 2022 by John Pumford-Green
-Page last updated: ~~LASTMOD~~
-{{tag>pi radio allstar mb7aze}}