Differences

This shows you the differences between two versions of the page.

--- public:radio:gm4slv_allstar [24/04/23 18:59 BST] – [Config] john
+++ public:radio:gm4slv_allstar [26/04/23 14:39 BST] (current) – removed john
@@ Line 1: / Line 1: @@
-<-[[.:start]]
-====== GM4SLV Allstar ======
-** UHF Allstar Gateway **
-===== Hardware =====
-|Platform|Rapsberry Pi|
-|Interface|CM108 Soundcard|
-|Radio|FT-8900|
-|Frequency|430.050MHz|
-|Monitor|[[http://gm4slv.plus.com:42111/allmon2/link.php?nodes=48148|Allmon2]]|
-|AllStar | [[http://stats.allstarlink.org/stats/48148]]|
-===== Config =====
-{{ :public:radio:gm4slv_allstar_config.tar | /etc/asterisk/ files }}
-===== Commands =====
- * DTMF Commands
-  * Please send * 7 3 to ensure all links are disconnected before making any new links
-^Command	^DTMF Sequence^
-|Disconect from Node xxxx	|  * 1 xxxx  |
-|Connect RX Only to xxxx	|  * 2 xxxx  |
-|Connect Transceive to xxxx	|  * 3 xxxx  |
-|Speak the Node Status	|  * 7 0  |
-|Disconnect ALL nodes	|  * 7 3  |
-|Reconnect ALL nodes	|  * 7 4  |
-|Send Node ID	|  * 8 0  |
-|Speak the Local Time	|  * 8 1  |
-|Parrot ON	|  * 9 1  |
-|Parrot OFF	|  * 9 2  |
-|Parrot ONCE	|  * 9 3  |
-^  Name  ^* 5 Macro shortcut to...	^  DTMF Sequence  ^  Node No.  ^
-|  Hubnet  |Disconnect from Hubnet	|  * 5 1 1  |  41223  |
-|  Hubnet  |Connect RX Only to Hubnet	|  * 5 2 1  |  41223  |
-|  Hubnet  |Connect Transceive to Hubnet	|  * 5 3 1  |  41223  |
-===== Courtesy Tones =====
-Can give information about the node status.
-After a local Transmission on the "input" frequency the reponse will be one of:
-  * Morse Letter **I** (di-dit) = node is not connected to any other nodes
-  * Morse Letter **R** (di-dah-dit) = node is connected in "Monitor/RX only" mode to one or more nodes
-  * Morse Letter **K** (dah-di-dah) = node is connected in "Transceive" mode to one or more nodes
-There are other tones, e.g. when a station on a linked node unkeys there's a low-pitched "bloop"
-When a local RF station sends a command there's a "bip bip" (not to be confused with the Morse letter I)
-===== Echolink =====
-AllStar nodes can also connect to [[https://www.echolink.org/logins.jsp|Echolink]]
-The node can connected to Echolink as ''GM4SLV-L ''
-(**UPDATE** --- //John Pumford-Green 24/04/23 14:47// )
-I have disabled the Echolink connection by editing ''/etc/asterisk/modules.conf'' to change the channel driver for Echolink to ''noload'' ->
-<code conf>
-noload => chan_echolink.so ;
-</code>
-an Asterisk reload is necessary:
-<code bash>
-gm4slv@mb7aze:/etc/asterisk$ sudo astres.sh
-Restarting Asterisk
-systemctl restart asterisk.service
-</code>
---- //John Pumford-Green 24/04/23 14:44//
-===== Further Information =====
-{{tag>}}