Differences

This shows you the differences between two versions of the page.

--- public:radio:allstar [29/05/22 17:36 BST] – [Page Info] gm4slv
+++ public:radio:allstar [26/04/23 14:48 BST] (current) – removed john
@@ Line 1: / Line 1: @@
-<-[[.:start]]
-====== MB7AZE Allstar Config ======
-===== all /etc/asterisk files =====
-{{ :private:greenmeadow:allstar_conf.tar |}}
-===== Main Config files =====
-=== echolink.conf ===
-++++ /etc/asterisk/echolink.conf |
-<code>
-[el0]
-call = MB7AZE-L                          ; Change this!
-pwd = oldtrout                           ; Change this!
-name = John                        ; Change this!
-qth = allstar 481481                           ; Change this!
-email = gm4slv@gm4slv.plus.com                         ; Change this!
-node = 879598                           ; Change this!
-; Data for EchoLink Status Page
-lat = 60.2883                               ; Latitude in decimal degrees
-lon = -001.42533                               ; Longitude in decimal degrees
-freq = 430.050                              ; not mandatory Frequency in MHz
-tone = 0.0                              ; not mandatory CTCSS Tone (0 for none)
-power = 1                               ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts)
-height = 0                              ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet)
-gain = 0                                ; Gain in db (0-9)
-dir = 0                                 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction)
-maxstns = 5                            ; Max Stations
-rtcptimeout = 10
-recfile = /tmp/echolink_recorded.gsm    ;
-astnode = 481481             ; Change this!
-context = radio-secure                  ; Default in code is echolink-in
-; Max 3 servers
-server1 = nasouth.echolink.org
-server2 = naeast.echolink.org
-server3 = server3.echolink.org
-; To deny w6xxx you would add the statement: deny = w6xxx
-; To prohibit computer-based connections you would write: permit = *-*
-; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
-; permit                                ; comma delimited list of callsign, type (-r)
-; deny
-; Remote text commands thru netcat:
-; o.conip <IPaddress>    (request a connect)
-; o.dconip <IPaddress>   (request a disconnect)
-; o.rec                  (turn on/off recording)
-; ipaddr
-; port
-</code>
-++++
-=== manager.conf ===
-++++ /etc/asterisk/manager.conf |
-<code>
-;
-; Asterisk Call Management support
-;
-; By default asterisk will listen on localhost only.
-[general]
-enabled = yes
-port = 5038
-bindaddr = 127.0.0.1
-[gm4slv]
-secret = llcgi
-read = all,system,call,log,verbose,command,agent,user,config
-write = all,system,call,log,verbose,command,agent,user,config
-</code>
-++++
-=== rpt.conf ===
-++++ /etc/asterisk/rpt.conf |
-<code>
-; Radio Repeater configuration file (for use with app_rpt)
-; Your Repeater
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-;
-; This is where you define your nodes which can be connected to.
-;
-[nodes]
-; Note, if you are using automatic update for allstar link nodes,
-; no allstar link nodes should be defined here. Only place a definition
-; for your local nodes, and private (off of allstar link) nodes here.
-;481480 = radio@127.0.0.1:4569/481480,NONE	; This must be changed to your node number
-= radio@127.0.0.1:4569/481481,NONE	; This must be changed to your node number
-                                        ; and iax port number if not the default
-;[481480]					; Change this to your assigned node number
-[481481]					; Change this to your assigned node number
-                                        ; Must also be enabled in modules.conf
-					; Rx audio/signalling channel. Choose ONLY 1 per node stanza
-					; Enable the selected channel driver in modules.conf !!!
-;rxchannel = dahdi/pseudo	        ; No radio (hub)
- rxchannel = SimpleUSB/usb_48148	; SimpleUSB
-; rxchannel = Pi/1                      ; Raspberry Pi PiTA
-; rxchannel = Radio/usb_48148		; USBRadio (DSP)
-; rxchannel = Dahdi/1			; PCI Quad card
-; rxchannel = Beagle/1			; BeagleBoard
-; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
-; rxchannel = Voter/48148                ; RTCM device
-duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.
-                                        ;     Special Case: Full duplex if linktolink is set to yes.
-                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.
-					;     Comment out idrecording and idtalkover to suppress IDs also
-                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.
-                                        ;     This mode is preferred when interfacing a simplex node.
-                                        ; 2 = Full Duplex with telemetry tones and hang time.
-                                        ;     This mode is preferred when interfacing a repeater.
-                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.
-                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
-linktolink = no				; disables forcing physical half-duplex operation of main repeater while
-					; still keeping half-duplex semantics (optional)
-linkmongain = 0				; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.
-					; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.
-					; If linkmongain set to a positive number monitored audio will increase by the set amount in db.
-					; The value of linkmongain is in db. The default value is 0 db.
-erxgain = -3				; Echolink receive gain adjustment
-					; Note: Gain is in db-volts (20logVI/VO)
-etxgain = 3				; Echolink transmit gain adjustment
-					; Note: Gain is in db-volts (20logVI/VO)
-eannmode = 2                           ; 1 = Say only node number on echolink connects (default = 1)
-                                        ; 2 = say phonetic call sign only on echolink connects
-                                        ; 3 = say phonetic call sign and node number on echolink connects
-;controlstates = controlstates		; system control state stanza
-scheduler = schedule			; scheduler stanza
-functions = functions			; Repeater Function stanza
-phone_functions = functions		; Phone Function stanza
-link_functions = functions		; Link Function stanza
-telemetry = telemetry			; Telemetry stanza
-morse = morse				; Morse stanza
-wait_times = wait-times			; Wait times stanza
-context = radio				; dialing context for phone
-callerid = "Repeater" <0000000000>	; callerid for phone calls
-accountcode = RADIO                     ; account code (optional)
-hangtime = 200				; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)
-althangtime = 300			; longer squelch tail
-totime = 300000				; 5 mins (12/4/22) transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)
-telemnomdb = -3				;
-telemduckdb = -10			;
-;idrecording = /home/gm4slv/gm4slv_id
-;idrecording = /home/gm4slv/mb7aze_id
-idrecording = |iDE MB7AZE			; Main ID message
-;idtalkover = |iMB7AZE			; Talkover ID message
-idtalkover = |iMB7AZE			; Talkover ID message
-					; See Telemetry section Example: idrecording = rpt/nodenames/48148
-idtime = 900000				; 15 mins (12/4/22) id interval time (in ms) (optional) Default 5 minutes (300000 ms)
-politeid = 30000			; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)
-unlinkedct = ct12			; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)
-remotect = ct3				; remote linked courtesy tone (indicates a remote is in the list of links)
-linkunkeyct = ct4			; sent when a transmission received over the link unkeys
-;nolocallinkct = 0			; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).
-; Supermon smlogger
-connpgm=/usr/local/sbin/supermon/smlogger 1
-discpgm=/usr/local/sbin/supermon/smlogger 0
-;connpgm = yourconnectprogram		; Disabled. Execute a program you specify on connect. (default)
-					; passes 2 command line arguments to your program:
-					; 1. node number in this stanza (us)
-					; 2. node number being connected to us (them)
-;discpgm = yourdisconnectprogram	; Disabled. Execute a program you specify on disconnect. (default)
-					; passes 2 command line arguments to your program:
-					; 1. node number in this stanza (us)
-					; 2. node number being disconnected from us (them)
-lnkactenable = 0			; Set to 1 to enable the link activity timer. Applicable to standard nodes only.
-lnkacttime = 3600			; Link activity timer time in seconds.
-lnkactmacro = *73			; Function to execute when link activity timer expires.
-lnkacttimerwarn = custom/timeout		; Message to play when the link activity timer has 30 seconds left.
-;remote_inact_timeout =	60		; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)
-;remote_timeout =			; Session time out for remote base. Set to 0 to disable. (60 * 60)
-;remote_timeout_warning_freq =		; 30
-;remote_timeout_warning =		; (3 * 60)
-;nounkeyct = 0				; Set to a 1 to eliminate courtesy tones and associated delays.
-holdofftelem = 0			; Hold off all telemetry when signal is present on receiver or from connected nodes
-					; except when an ID needs to be done and there is a signal coming from a connected node.
-telemdefault = 1                        ; 0 = telemetry output off
-                                        ; 1 = telemetry output on (default = 1)
-                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.
-telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,
-                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)
-beaconing = 1				; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)
-parrotmode = 1				; 0 = Parrot Off (default = 0)
-					; 1 = Parrot On Command
-					; 2 = Parrot Always
-					; 3 = Parrot Once by Command
-parrottime = 1000			; Set the amount of time in milliseconds
-					; to wait before parroting what was received
-;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified
-                                        ; b/w. app_rpt must have been compiled with
-                                        ; the notch option
-startup_macro = *80*81*70
-; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign	; Point to alternate nodename sound directory
-; Stream your node audio to Broadcastify or similar. See https://wiki.allstarlink.org/wiki/Stream_Node_Audio_to_Broadcastify
-; outstreamcmd = /bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - | /usr/bin/ezstream -qvc /etc/ezstream.xml
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Need more information on these
-;extnodes = extnodes-different	; section in extnodefile containing dynamic node information (optional)
-;extnodefile = /home/gm4slv/rpt_extnodes	; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)
-;extnodefile2 =			; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????
-;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames
-;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)
-;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)
-;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set
-;                               ; to support tail messages. They can be omitted otherwise.
-;tailmessagetime = 300000       ; Play a tail message every 5 mins
-;tailsquashedtime = 30000       ; If squashed by another user,
-;                               ; try again after 30 seconds
-;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message
-; alt_functions
-; ctgroup
-; dphone_functions
-; idtime
-; iobase
-; iospeed
-; locallist
-; mars		Remote Base
-; memory
-; nobusyout
-; nodes
-; nolocallinkct
-; notelemtx
-; outxlat
-; parrot
-; propagate_phonedtmf
-; rptnode
-; rptinactmacro  Macro to execute when inactivity timer expires
-; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)
-; rxnotch	Optional Audio notch
-; simplexphonedelay
-; tonemacro
-; tonezone
-; txlimits
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; *** Status Reporting ***
-; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org
-statpost_url = http://stats.allstarlink.org/uhandler ; Status updates
-[functions]
-; Prefix	Functions
-; *1		Disconnect Link
-; *2		Monitor Link
-; *3		Connect Link
-; *4		Command Mode
-; *5		Macros
-; *6		User Functions
-; *7		Connection Status/Functions
-; *8		User Functions
-; *9		User Functions
-; *0		User Functions
-; *A		User Functions
-; *B		User Functions
-; *C		User Functions
-; *D		User Functions
-; Mandatory Command Codes
-= ilink,1		; Disconnect specified link
-= ilink,2		; Connect specified link -- monitor only
-= ilink,3		; Connect specified link -- tranceive
-= ilink,4		; Enter command mode on specified link
-= ilink,5		; System status
-;99 = cop,6              ; PTT (phone mode only)
-; End Mandatory Command Codes
-= ilink,6		; Disconnect All Links
-= ilink,16		; Reconnect links disconnected with "disconnect all links"
-= status,11         ; Force ID (local only)
-= status,12         ; Give Time of Day (local only)
-= cop,21		; Enable Parrot Mode
-= cop,22		; Disable Parrot Mode
-= cop,55		; Parrot Once if parrot mode is disabled
-= cop,2		; System enable
-= cop,3		; System disable
-= cop,1				; System warm boot
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Macro Commands
-= macro
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Autopatch Commands
-; Note, This may be a good place for other 2 digit frequently used commands
-;61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up
-;62 = autopatchdn                                                 ; Autopatch down
-; autopatchup can optionally take comma delimited setting=value pairs:
-; context = string		; Override default context with "string"
-; dialtime = ms			; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)
-; farenddisconnect = 1		; Automatically disconnect when called party hangs up
-; noct = 1			; Don't send repeater courtesy tone during autopatch calls
-; quiet = 1			; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up
-				; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Status Commands
-; 1 - Force ID (global)
-; 2 - Give Time of Day (global)
-; 3 - Give software Version (global)
-; 4 - Give GPS location info
-; 5 - Last (dtmf) user
-; 11 - Force ID (local only)
-; 12 - Give Time of Day (local only)
-;721 = status,1          ; Force ID (global)
-;722 = status,2          ; Give Time of Day (global)
-;723 = status,3          ; Give software Version (global)
-;724 = status,4          ; Give GPS location info
-;725 = status,5          ; Last (dtmf) user
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Link Commands
-; 1 - Disconnect specified link
-; 2 - Connect specified link -- monitor only
-; 3 - Connect specified link -- tranceive
-; 4 - Enter command mode on specified link
-; 5 - System status
-; 6 - Disconnect all links
-; 7 - Last Node to Key Up
-; 8 - Connect specified link -- local monitor only
-; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
-; 10 - Disconnect all RANGER links (except permalinks)
-; 11 - Disconnect a previously permanently connected link
-; 12 - Permanently connect specified link -- monitor only
-; 13 - Permanently connect specified link -- tranceive
-; 15 - Full system status (all nodes)
-; 16 - Reconnect links disconnected with "disconnect all links"
-; 17 - MDC test (for diag purposes)
-; 18 - Permanently Connect specified link -- local monitor only
-; ilink commands 1 through 5 are defined in the Mandatory Command section
-;806 = ilink,6			; Disconnect all links
-;827 = ilink,7			; Last Node to Key Up
-;808 = ilink,8			; Connect specified link -- local monitor only
-;809 = ilink,9,48148,"Testing"	; would send a text message to node 48148 replace 48148 with 0 for all connected nodes
-;810 = ilink,10			; Disconnect all RANGER links (except permalinks)
-;811 = ilink,11			; Disconnect a previously permanently connected link
-;812 = ilink,12			; Permanently connect specified link -- monitor only
-;823 = ilink,13			; Permanently connect specified link -- tranceive
-;815 = ilink,15			; Full system status (all nodes)
-;817 = ilink,17			; MDC test (for diag purposes)
-;818 = ilink,18			; Permanently Connect specified link -- local monitor only
-;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
-; Control operator (cop) functions.
-; Change these to something other than these codes listed below!
-; Uncomment as needed.
-;901 = cop,1				; System warm boot
-; 904 = cop,4				; Test tone on/off (toggle)
-; 905 = cop,5				; Dump system variables on console (debug use only)
-; 907 = cop,7				; Time out timer enable
-; 908 = cop,8				; Time out timer disable
-; 909 = cop,9				; Autopatch enable
-; 910 = cop,10				; Autopatch disable
-; 911 = cop,11				; User linking functions enable
-; 912 = cop,12				; User linking functions disable
-; 913 = cop,13				; Query system control state
-; 914 = cop,14				; Set system control state
-; 915 = cop,15				; Scheduler enable
-; 916 = cop,16				; Scheduler disable
-; 917 = cop,17				; User functions enable (time, id, etc)
-; 918 = cop,18				; User functions disable
-; 919 = cop,19				; Select alternate hang time (althangtime)
-; 920 = cop,20				; Select standard hangtime (hangtime)
-; 924 = cop,24				; Flush all telemetry
-; 925 = cop,25				; Query last node un-keyed
-; 926 = cop,26				; Query all nodes keyed/unkeyed
-; 927 = cop,27				; Reset DAQ minimum on a pin
-; 928 = cop,28				; Reset DAQ maximum on a pin
-; 930 = cop,30				; Recall Memory Setting in Attached Xcvr
-; 931 = cop,31				; Channel Selector for Parallel Programmed Xcvr
-; 932 = cop,32				; Touchtone pad test: command + Digit string + # to playback all digits pressed
-; 933 = cop,33				; Local Telemetry Output Enable
-; 934 = cop,34				; Local Telemetry Output Disable
-; 935 = cop,35				; Local Telemetry Output on Demand
-; 936 = cop,36				; Foreign Link Local Output Path Enable
-; 937 = cop,37				; Foreign Link Local Output Path Disable
-; 938 = cop,38				; Foreign Link Local Output Path Follows Local Telemetry
-; 939 = cop,39				; Foreign Link Local Output Path on Demand
-; 942 = cop,42				; Echolink announce node # only
-; 943 = cop,43				; Echolink announce node Callsign only
-; 944 = cop,44				; Echolink announce node # & Callsign
-; 945 = cop,45				; Link Activity timer enable
-; 945 = cop,46				; Link Activity timer disable
-; 947 = cop,47				; Reset "Link Config Changed" Flag
-; 948 = cop,48				; Send Page Tone (Tone specs separated by parenthesis)
-; 949 = cop,49				; Disable incoming connections (control state noice)
-; 950 = cop,50				; Enable incoming connections (control state noicd)
-; 951 = cop,51				; Enable sleep mode
-; 952 = cop,52				; Disable sleep mode
-; 953 = cop,53				; Wake up from sleep
-; 954 = cop,54				; Go to sleep
-; 956 = cop,56                            ; Rx CTCSS Enable
-; 957 = cop,57                            ; Rx CTCSS Disable
-; 958 = cop.58                            ; Tx CTCSS On Input only Enable
-; 959 = cop,59                            ; Tx CTCSS On Input only Disable
-; 960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
-;                                         ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
-;                                         ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.
-;                                         ; DestID and subcode are only specified for  the 'C' type message.
-;                                         ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of
-;                                         ; the radio being called, and the subcodes are as follows:
-;                                         ; Subcode '8205' is Voice Selective Call for Spectra ('Call')
-;                                         ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or
-;                                         ; Astro-Saber('Call')
-;                                         ; Subcode '810D' is Call Alert (like Maxtrac 'CA')
-; 961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
-; 962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
-; 963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])
-; 964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
-; 965 = cop,65                            ; Send POCSAG page (equipped channel types only)
-[functions-remote]
-= remote,1                            ; Retrieve Memory
-= remote,2                            ; Set freq.
-= remote,3                            ; Set tx PL tone
-= remote,4                            ; Set rx PL tone
-= remote,100                         ; Rx PL off
-= remote,101                         ; Rx PL on
-= remote,102                         ; Tx PL off
-= remote,103                         ; Tx PL on
-= remote,104                         ; Low Power
-= remote,105                         ; Medium Power
-= remote,106                         ; High Power
-= remote,107                        ; Bump -20
-= remote,108                        ; Bump -100
-= remote,109                        ; Bump -500
-= remote,110                        ; Bump +20
-= remote,111                        ; Bump +100
-= remote,112                        ; Bump +500
-= remote,113                        ; Scan - slow
-= remote,114                        ; Scan - quick
-= remote,115                        ; Scan - fast
-= remote,116                        ; Scan + slow
-= remote,117                        ; Scan + quick
-= remote,118                        ; Scan + fast
-= remote,119                         ; Tune
-= remote,5                           ; Long status query
-= remote,140				; Short status query
-= remote,210				; Send a *
-= remote,211				; Send a #
-;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.
-                                        ; Define a different dtmf sequence for each user which is
-                                        ; authorized to use the remote base to control access to it.
-                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to
-                                        ; the remote base and announce WB6NIL as being logged in.
-                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to
-                                        ; the remote base and announce WA6ZFT as being logged in.
-                                        ; When the remote base is disconnected from the originating node, the
-                                        ; user will be logged out. The LICENSETAG argument is used to enforce
-					; tx frequency limits. See [txlimits] below.
-= cop,6                              ; Remote base telephone key
-[telemetry]
-; Telemetry entries can be shared across all repeaters, or defined for each repeater.
-; Can be a tone sequence, morse string, or a file
-;
-; |t - Tone escape sequence
-;
-; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)
-; Single frequencies are created by setting freq1 or freq2 to zero.
-;
-; |m - Morse escape sequence
-;
-; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the
-; [morse] section.
-;
-; Follow with an alphanumeric string
-;
-; |i - Morse ID escape sequence
-;
-; Sends Morse code at the ID amplitude and ID frequency as defined in the
-; [morse] section.
-;
-; path/to/sound/file/without/extension
-;
-; Send the sound if in place of a constructed tone. Do not include the file extension
-; Example: ct8 = rpt/bloop
-; Example: idrecording = rpt/nodenames/48148
-ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
-ct2 = |t(660,880,150,2048)
-ct3 = |t(440,0,150,4096)
-ct4 = |t(550,0,150,2048)
-ct5 = |t(660,0,150,2048)
-ct6 = |t(880,0,150,2048)
-ct7 = |t(660,440,150,2048)
-ct8 = |t(700,1100,150,2048)
-ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
-remotemon = |mR
-;remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only
-remotetx = |mK
-;remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)		; local courtesy tone when linked Trancieve mode
-cmdmode = |t(900,903,200,2048)
-;functcomplete = |mW
-functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
-remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
-pfxtone = |t(350,440,30000,3072)
-patchup = rpt/callproceeding
-patchdown = rpt/callterminated
-ct12 = |mI
-ct13 = |mR
-; As far as what the numbers mean,
-; (000,000,010,000)
-;   |   |   |   |-------amplitude
-;   |   |   |-------------duration
-;   |   |-------------------Tone 2
-;   |-------------------------Tone 1
-; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
-; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)
-; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.
-; Morse code parameters, these are common to all repeaters.
-[morse]
-speed = 18				; Approximate speed in WPM
-frequency = 800				; Morse Telemetry Frequency
-amplitude = 4096			; Morse Telemetry Amplitude
-idfrequency = 1065			; Morse ID Frequency
-idamplitude = 1024			; Morse ID Amplitude
-;
-; This section allows wait times for telemetry events to be adjusted
-; A section for wait times can be defined for every repeater
-;
-[wait-times]
-telemwait = 400                        ; Time to wait before sending most telemetry
-idwait = 500                            ; Time to wait before starting ID
-unkeywait = 200                        ; Time to wait after unkey before sending CT's and link telemetry
-calltermwait = 2000                     ; Time to wait before announcing "call terminated"
-; Memories for remote bases
-[memory]
-;00 = 146.580,100.0,m
-;01 = 147.030,103.5,m+t
-;02 = 147.240,103.5,m+t
-;03 = 147.765,79.7,m-t
-;04 = 146.460,100.0,m
-;05 = 146.550,100.0,m
-; Place command macros here
-[macro]
-= *141223# ; disc. hubnet
-= *241223# ; monitor hubnet
-= *341223# ; transceive hubnet
-= *12197# ; disc Freestar
-= *22197# ; monitor Freestar
-= *32197# ; transceive Freestar
-= *129332# ; disc Alaska
-= *229332# ; monitor Alaska
-= *329332# ; transceive Alaska
-= *154383# ; disc CQ North
-= *254383# ; monitor CQ North
-= *354383# ; transceive CQ North
-= *140894# ; disconnect hubnet Echo
-= *340894# ; connect hubnet echo
-= *13009999#	; dis echolink echotest
-= *33009999#	; con echolink echotest
-; Data Acquisition configuration
-;[daq-list]
-;device = device_name1
-;device = device_name2
-;Where: device_name1 and device_name2 are stanzas you define in this file
-;device = daq-cham-1
-; Device name
-;[daq-cham-1]				; Defined in [daq-list]
-;hwtype = uchameleon			; DAQ hardware type
-;devnode = /dev/ttyUSB0			; DAQ device node (if required)
-;1 = inadc				; Pin definition for an ADC channel
-;2 = inadc
-;3 = inadc
-;4 = inadc
-;5 = inadc
-;6 = inadc
-;7 = inadc
-;8 = inadc
-;9 = inp				; Pin definition for an input with a weak pullup resistor
-;10 = inp
-;11 = inp
-;12 = inp
-;13 = in				; Pin definition for an input without a weak pullup resistor
-;14 = out				; Pin definition for an output
-;15 = out
-;16 = out
-;17 = out
-;18 = out
-;[meter-faces]
-;face = scale(scalepre,scalediv,scalepost),word/?,...
-;
-; scalepre = offset to add before dividing with scalediv
-; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).
-; scalepost = offset to add after dividing with scalediv
-;
-;face = range(X-Y:word,X2-Y2:word,...),word/?,...
-;face = bit(low-word,high-word),word/?,...
-;
-; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,
-; or a question mark which is  a placeholder for the measured value.
-;
-;
-; Battery voltage 0-20 volts
-;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
-; 4 quadrant wind direction
-;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
-; LM34 temperature sensor with 130 deg. F full scale
-;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
-; Status poll (non alarmed)
-;light = bit(ha/off,ha/on),ha/light,?
-;[alarms]
-;
-;tag = device,pin,node,ignorefirst,func-low,func-hi
-;
-;tag = a unique name for the alarm
-;device = daq device to poll
-;pin = the device pin to be monitored
-;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it
-;node = the node number to execute the function on
-;func-low = the DTMF function to execute on a high to low transition
-;func-high = the DTMF function to execute on a low to high transition
-;
-; a  '-' as a function name is shorthand for no-operation
-;
-;door = daq-cham-1,9,1,2017,*7,-
-;pwrfail = daq-cham-1,10,0,2017,*911111,-
-;
-; Control states
-; Allow several control operator functions to be changed at once using one command (good for scheduling)
-;
-;[controlstates]
-;statenum = copcmd,[copcmd]...
-;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation
-;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation
-;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation
-; Scheduler - execute a macro at a given time
-[schedule]
-;dtmf_function =  m h dom mon dow  ; ala cron, star is implied
-;8 = 55 12 * * *   ; at midnight, execute macro 2.
-; See https://wiki.allstarlink.org/wiki/Event_Management
-[events]
-#includeifexists custom/rpt.conf
-</code>
-++++
-=== simpleusb.conf ===
-++++ /etc/asterisk/simpleusb.conf |
-<code>
-; If you are going to use this channel driver, you MUST enable it in modules.conf
-; change:
-; noload => chan_simpleusb.so ;                   CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
-; to:
-; load => chan_simpleusb.so ;                   CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
-; SimpleUSB configuration
-[general]
-[usb_48148]
-eeprom = 0              ; EEPROM installed: 0,1
-                        ; 0 = no (default)
-                        ; 1 = yes
-hdwtype = 0		; Leave this set to 0 for USB sound fobs modified using
-			; the instructions from usbfob.pdf. Use a setting of
-			; 1 is for Dingotel/Sph interfaces.
-; Receiver parameters
-rxboost = 0             ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
-                        ; Set to 1 for additonal gain if using a low-level receiver output
-carrierfrom = usb ; no,usb,usbinvert
-                        ; no - no carrier detection at all
-                        ; usb - from the COR line on the USB sound fob (Active high)
-                        ; usbinvert - from the inverted COR line on the USB sound fob (Active low)
-ctcssfrom = no		; no,usb,usbinvert
-                        ; no - CTCSS decoding, system will be carrier squelch
-                        ; usb - CTCSS decoding using input from USB sound fob (Active high)
-                        ; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low)
-deemphasis = yes         ; enable de-emphasis (input from discriminator)
-plfilter = no           ; enable PL filter
-;rxondelay = 0		; number of 20ms intervals to hold off receiver turn-on indication
-; Transmitter parameters
-txmixa = voice          ; Left channel output (A): no,voice
-                        ; no - Do not output anything
-                        ; voice - output voice only
-txmixb = no		; Right channel output (B): no,voice
-                        ; no - Do not output anything
-                        ; voice - output voice only
-txboost = 0
-invertptt = 0           ; Invert PTT: 0,1
-                        ; 0 - ground to transmit
-                        ; 1 - open to transmit
-preemphasis = yes	; Perform standard 6db/octave pre-emphasis
-; pager = no            ; no,a,b (e.g. pager = b means "put the normal repeat audio on channel A, and the pager audio on channel B")
-; duplex3 = 0           ; duplex 3 gain setting (0 to disable)
-duplex = 0              ; Duplex 0,1
-                        ; 0 - half duplex
-                        ; 1 - full duplex
-#includeifexists custom/simpleusb.conf
-</code>
-++++
-=== simpleusb_tune_usb_48148.conf ===
-++++ /etc/asterisk/simpleusb_tune_usb_48148.conf |
-<code>
-[usb_48148]
-; name=usb_48148
-; devicenum=1
-devstr=1-1.2:1.0
-rxmixerset=330
-txmixaset=70
-txmixbset=50
-</code>
-++++
-=== crontab ===
-''00 * * * * sudo /usr/sbin/asterisk -rx "rpt localplay 481481 /home/gm4slv/mb7aze_id " >/dev/null 2>&1''
-''00 * * * * sleep 4 && sudo /usr/sbin/asterisk -rx "rpt fun 481481 *81" >/dev/null 2>&1''
-  * ID file (a uLaw audio file) for verbal announcements {{ :private:greenmeadow:mb7aze_id.zip |}}
-==== allmon2 and supermon web files ====
-=== allmon2 ===
-{{ :private:greenmeadow:allmon2.tar |}}
-=== supermon ===
-{{ :private:greenmeadow:supermon.tar |}}
-==== Page Info ====
-Page created Sun May 29 15:48:50 2022 by John Pumford-Green
-Page last updated: ~~LASTMOD~~
-{{tag>pi radio allstar mb7aze}}