public:radio:2024:allstar
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| public:radio:2024:allstar [07/04/24 19:34 BST] – [Section Two] john | public:radio:2024:allstar [06/03/25 06:49 GMT] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 8: | Line 8: | ||
| ===== Node 48148 ===== | ===== Node 48148 ===== | ||
| - | I've set up an Allstar node/ | + | I've set up an Allstar node/ |
| - | It turned out to be not too difficult, as I already had all the correct working configs from the last time I used Allstar, so I was able to copy them onto the new SD card image and have a working node straight from boot up! | + | |Platform|Rapsberry Pi| |
| + | |Interface|CM108 Soundcard| | ||
| + | |Radio|FT-8900| | ||
| + | |Frequency|144.9125 MHz| | ||
| + | |Monitor|[[http:// | ||
| + | |AllStar | [[http:// | ||
| - | === Editing the image == | + | |
| + | It turned out to be not too difficult, as I already had all the correct working configs from [[public: | ||
| + | |||
| + | ==== Editing the image === | ||
| I downloaded the most recent V2.0 beta image for Raspberry Pi here : [[http:// | I downloaded the most recent V2.0 beta image for Raspberry Pi here : [[http:// | ||
| Line 25: | Line 33: | ||
| - | Then '' | + | Then |
| + | |||
| + | '' | ||
| and wait. | and wait. | ||
| - | === It's alive === | + | ==== It's alive ==== |
| Once written I put the CD card into the Pi. Booted up, and heard my callsign ID on the radio - it worked, without having to go through the rigmarole of a new install configuration. | Once written I put the CD card into the Pi. Booted up, and heard my callsign ID on the radio - it worked, without having to go through the rigmarole of a new install configuration. | ||
| Line 35: | Line 45: | ||
| I SSH'd in via the DHCP address it had been given, and to change the IP to a static one I checked the peculiar name of the Ethernet interface: '' | I SSH'd in via the DHCP address it had been given, and to change the IP to a static one I checked the peculiar name of the Ethernet interface: '' | ||
| - | < | + | < |
| # Example static IP configuration: | # Example static IP configuration: | ||
| interface enxb827eb6f9954 | interface enxb827eb6f9954 | ||
| Line 45: | Line 55: | ||
| Reboot again, and now I can SSH via the correct static IP address | Reboot again, and now I can SSH via the correct static IP address | ||
| - | Next Steps | + | ==== Next Steps ==== |
| - | * Add my own user (don't want to use the built in '' | + | * Add my own user (don't want to use the built in '' |
| * Add myself to the necessary groups (sudo etc.) | * Add myself to the necessary groups (sudo etc.) | ||
| + | * change the hostname from '' | ||
| + | * remember to edit ''/ | ||
| + | * set timezone to '' | ||
| * Check the RX/TX levels/ | * Check the RX/TX levels/ | ||
| * Enable Echolink by editing ''/ | * Enable Echolink by editing ''/ | ||
| * Copy any necessary '' | * Copy any necessary '' | ||
| * Port Forward on router: | * Port Forward on router: | ||
| - | * UDP/4569 | + | * '' |
| - | * UDP/5198 | + | * '' |
| - | * UDP/5199 | + | * '' |
| * All working...! | * All working...! | ||
| + | |||
| + | ==== First QSO ==== | ||
| + | |||
| + | * I was called on Echolink by '' | ||
| ===== Section Two ===== | ===== Section Two ===== | ||
| Line 64: | Line 81: | ||
| * some macros as configured in ''/ | * some macros as configured in ''/ | ||
| + | * < | ||
| - | < | + | < |
| [macro] | [macro] | ||
public/radio/2024/allstar.1712514897.txt.gz · Last modified: (external edit)