Differences

This shows you the differences between two versions of the page.

--- private:greenmeadow:mb7aze_allstar [29/05/22 16:00 BST] – [Commands] gm4slv
+++ private:greenmeadow:mb7aze_allstar [29/05/22 16:29 BST] (current) – removed gm4slv
@@ Line 1: / Line 1: @@
-<-[[.:start]]
-====== MB7AZE / Allstar ======
-FIXME
-<todo>add configuration details for running All Star on MB7AZE</todo>
-|Rapsberry Pi|
-|[[Allstar|All Star]]|
-|CM108 Soundcard|
-|FT-8900|
-|430.050MHz|
-[[https://ukrepeater.net/my_repeater.php?id=4823|NoV issued April 2022]]
-===== Commands =====
-  * DTMF Commands
-  * Please send * 7 3 to ensure all links are disconnected before making any new links
-^Command	^DTMF Sequence^
-|Disconect from Node xxxx	|* 1 xxxx|
-|Connect RX Only to xxxx	|* 2 xxxx|
-|Connect Transceive to xxxx	|* 3 xxxx|
-|Speak the Node Status	|* 7 0|
-|Disconnect ALL nodes	|* 7 3|
-|Reconnect ALL nodes	|* 7 4|
-|Send Node ID	|* 8 0|
-|Speak the Local Time	|* 8 1|
-|Parrot ON	|* 9 1|
-|Parrot OFF	|* 9 2|
-|Parrot ONCE	|* 9 3|
-To connect to an Echolink Node make node number 6 figures long
-with leading 0 s where needed and indicate it's an "Echolink"
-node with an extra leading 3 after usual connect sequence (* 3 )
-|For example to connect to 9999	|* 3 3 0 0 9 9 9 9|
-^* 5 Macro shortcut to...	^DTMF Sequence^
-|Connect RX Only to Hubnet	|* 5 2 1|
-|Connect Transceive to Hubnet	|* 5 3 1|
-|Disconnect from Hubnet	|* 5 1 1|
-|Connect RX Only to FreeNet	|* 5 2 2|
-|Connect Transceive to FreeNet	|* 5 3 2|
-|Disconnect from FreeNet	|* 5 1 2|
-|Connect RX Only to Alaska Morning Net	|* 5 2 3|
-|Connect Transceive to Alaska Morning Net	|* 5 3 3|
-|Disconnect from Alaska Morning Net	|* 5 1 3|
-|Connect RX Only to CQ North	|* 5 2 4|
-|Connect Transceive to CQ North	|* 5 3 4|
-|Disconnect from CQ North	|* 5 1 4|
-|Connect to Hubnet Echotest (40894)	|* 5 3 9 1|
-|Disconnect from Hubnet Echotest (40894)	|* 5 1 9 1|
-|Connect to Echolink Echotest(3009999)	|* 5 3 9 2|
-|Disconnect from Hubnet Echotest(3009999)	|* 5 1 9 2|
-==== Courtesy Tones ====
-Can give information about the node status.
-After a local Transmission on the "input" frequency the reponse will be one of:
-  * Morse Letter I (di-dit) = node is not connected to any other nodes
-  * Morse Letter R (di-dah-dit) = node is connected in "Monitor/RX only" mode to one or more nodes
-  * Morse Letter K (dah-di-dah) = node is connected in "Transceive" mode to one or more nodes
-There are other tones, e.g. when a station on a linked node unkeys there's a low-pitched "bloop"
-When a local RF station sends a command there's a "bip bip" (not to be confused with the Morse letter I)
-Also connected to [[https://www.echolink.org/logins.jsp|Echolink]] as ''MB7AZE-L #879598''
-==== Page Info ====
-Page created Sun May 29 12:18:09 2022 by John Pumford-Green
-Page last updated: ~~LASTMOD~~
-{{tag>pi radio allstar}}